E-FLITE CARBON-Z CESSNA 150T 2.1M BNF BASIC
Large tires and a wide flight envelope make for a versatile aircraft
By Greg Gimlick | maelelectrics@gimlick.com
Photos by the author

MY FIRST IMPRESSION was that the box was so big that the FedEx driver was dwarfed by it! The airplane itself is remarkably well packaged in its custom-fit foam case, and each part was protected by plastic or some other packaging.
The finish on the EPO foam surface was excellent. The tundra tires look massive and are way cool. All of the hardware was individually bagged for its particular assembly.
Assembly
Read the manual thoroughly ahead of time to familiarize yourself with the assembly process and radio programming. E-flite makes radio programming as simple as possible, and there are charts in the manual showing proper setups to work with the installed and preprogrammed Spektrum AR637TA receiver. You can also download the .SPM or .NSPM file that is appropriate for your transmitter. I compared the two and decided to program mine from the chart so that I could select a couple of different switches than what the factory file called for.
The rudder is the first assembly step and the only one requiring any glue. The CA hinges are fastened to the rudder and need to be glued into
At a Glance
Specifications
Model type: Aerobatic sport scale
Skill level: Beginner to expert
Wingspan: 83.7 inches
Wing area: 1,053 sq. in.
Length: 61.8 inches
Weight: 149 ounces with battery
Wing loading: 20.4 ounces per sq. ft.
Power system: E-flite BL50 brushless outrunner motor 525 Kv; Spektrum Avian 60-amp Smart ESC; 6S 5,000 mAh 30C Smart G2 LiPo battery: IC5 (required); E-flite 15 x 7 electric propeller
Construction: EPO foam
Requires: Spektrum six-channel transmitter; 4S to 6S 3,200 to 7,000 mAh LiPo battery
Price: $499.99
Test-Model Details
Radio system: Spektrum NX10 transmitter; Spektrum AR637T DSMX six-channel AS3X and SAFE telemetry receiver
Ready-to-fly weight: 149 ounces
Wing loading: 20.4 ounces per sq. ft.
Flight duration: 10-plus minutes (depending on battery capacity and flying style)
Pluses
- Quick and easy assembly.
- 4S to 6S power without reprogramming.
- Wide flight envelope for beginners to experts.
- ESC provides real-time battery voltage, current, motor rpm, and other data.
- Optional-use motor reversing for special ground handling.
- Spektrum AR637TA receiver with full-range telemetry.
- Six factory-installed, metal-geared servos.
- Excellent battery access to fit a wide range of flight batteries.
- Easy field assembly with integrated wiring connections.
Minuses
- Retention screws for horizontal stabilizer missing.
Manufacturer/Distributor
Horizon Hobby
(800) 338-4639
www.horizonhobby.com


The vertical stabilizer. Be careful to route the taillight wire in the groove on the left side of the stabilizer so that you can cover it with the provided red tape. When it is installed, the tape blends in perfectly. Two of the hinge slots on mine were slightly oversized and required some pressure until the glue set.
The tail wheel assembly and main landing gear are the next steps. They simply bolt into provided slots. A retention plate goes over the two-piece main landing gear, and an extra set of hands comes in handy to hold it while you install the first couple of screws.
The motor is included but not installed. The ESC is preinstalled in the fuselage, so it only requires plugging in once the motor is in place. The cross bracket is installed on the back of the motor and aligns with a preinstalled plastic mount to ensure proper thrust lines. The motor bolts have thread-lock on them from the factory.
After it is bolted in place, the foam cowling is attached with two screws, but be sure to plug in the landing light first. A collet, propeller, and spinner complete the motor installation. Check for proper rotation before installing the propeller.
If you’re going to use the optional thrust reversing, this is a good time to set that up and check for proper operation before you install the propeller.
The horizontal stabilizer halves slide over a joiner and interlock with each other. Two retention screws are used to lock it all in place. The control rod had a ball-joint connector to attach to the preinstalled horn, just like the rudder.
The main wing slides onto a joiner and is retained with a single thumbscrew for each side. As you set the root of the wing, ensure that the connectors all line up and are fully seated. There are no wires to connect because the connectors are built into the wing root and fuselage side. The wing struts are fastened to the fuselage with quick connectors. Because the quick-connect pins can be easily dropped and lost at the field, I taped a spare set to the inside of the cockpit/battery hatch.
With the assembly complete, take a few minutes to examine all of the components and ensure that they move properly and are secure. The hatch in the top of the fuselage allows access to the wing-retention screws and receiver area. The rudder connector wasn’t fully seated into the receiver, so take some time to check all of the connections there. I also secured a couple of wires so that they didn’t move around and contact the receiver antenna.

I did not have to adjust any linkages or programming for my setup to be in line with the suggested throws. Do not use any subtrim when setting up your throws. If they are not centered, adjust them mechanically.
Control Throws and CG
The center of gravity (CG) is set at 95mm to 105mm behind the leading edge as measured at the root of the wing. Throws are listed in the manual for high and low rates.
The airplane can be bound with SAFE Select activated or not. If you choose not to use it, you will have AS3X at all times regardless. I set mine up with SAFE activated and assigned a switch to turn it on and off.
A word of caution: If you’re using the optional motor reversing for braking, be sure not to set up the switch for that on the same channel as flight modes. If you do, it will reverse the motor in flight as you change modes. The manual guides you through this in two areas to ensure that you get it right.
The manual has the throttle reversing set on the switch that is usually used for the landing gear because this airplane has fixed gear. I was afraid of negative habit transfer and assigned it to a switch on the
transmitter that I seldom use. I was con-
cerned that I’d hit that gear switch without
thinking and activate the reverse in flight.
Options
I’ve already mentioned the program-
ming options for SAFE Select and throttle
reverse, but there are also some hardware
options available separately. E-flite has a
set of landing gear should you wish to
make the Cessna into a tricycle gear con-
figuration, and also a set of floats if you
want to fly off water. Both options appear
to be quick and easy to mount to the
airframe.
Flying
I did my test flight with SAFE off and
only AS3X active. Keep in mind that it isn’t
activated until the throttle has passed 25%
the first time, so do that on your preflight
check. With everything thoroughly
checked, it was time to take to the sky.
The weather was approximately 82° with
wind gusting 8 to 15 mph. There were no
surprises on the takeoff roll or climb. It
was stable, and more than ample power
was available with the 6S setup. After a
gentle climb and trip around the pattern
to check controls and the CG, it was off to
the races.
The big 150T is not a racer by any means,
but it has good speed and performance
that is far beyond scalelike. I haven’t tried
a 4S or 5S battery pack but have no doubt
that the aircraft would do fine with either.
I prefer higher voltage for my setups and
will stick with my 6S selection. The 6S pack
easily flies the model for 10 minutes. I
started with the timer set for six minutes
and increased it until I settled on 10.
The stall is gentle and straight ahead
with no tendency to drop a wing. Spins are
easily recovered from with little more than
relaxing the controls and letting it level
itself out. It just refused to stall and snap
to either side, which makes a great feature
for less experienced pilots. This model
could easily go from flight trainer to an
aerobatic trainer.
Loops are big and round, and rolls are
as axial as one would expect from a high-
wing design. Inverted flight requires a
slight bit of elevator to maintain, but it will
happily fly around like that all day. While
not designed to be a 3D aircraft, it will also
do a respectable hover with the 6S setup.
The flaps are quite effective and the sug-
gested elevator mix seems nearly perfect.
With the flaps fully deployed into the
10-mph wind, it slowed to a crawl. I got a
bit obsessed with trying to do zero rollout
landings. Of course, with the thrust rever-
sal for braking upon touchdown, we had
people wondering what was going on. The
airplane is a floater, so plan accordingly.
Conclusion
This airplane is simply a joy to fly—I
don’t know how else to put it. Everything
feels solid, and the AS3X does an excellent
job of dampening the effects of wind gusts
without ever feeling like you’re fighting an
over-zealous flight controller.
The SAFE Select is effective for what it’s
designed to do and nice to have if you let
an inexperienced pilot take a turn. The
Cessna 150T looks great in the air, flies like
a dream, and flight duration is more than
adequate. I’d say E-flite has another winner
in its lineup.








