FREE FLIGHT SPORT
FF OFFERINGS
By Don DeLoach | ddeloach@comcast.net

WE FREEFLIGHTERS are fortunate to have a handful of dedicated kit and supply providers. No one has ever gotten rich providing these specialized products, so I thought it was worthwhile to devote my column space this month to highlighting these offerings.
J&H Aerospace
Joshua and Hope Finn of J&H Aerospace are constantly churning out new laser-cut kits between their frequent trips to major meets across the country. Their latest kits are the Saturno P-30 and the Polly C Hand-Launch Glider (HLG).
The Saturno is Alexandre Cruz’s highly successful design that has won many contests (most recently, the 2021 Rocky Mountain Free Flight [FF] Champs in the hands of 6-year-old Caleb Finn). Alexandre reformatted the construction to suit modern laser-cutting, so the new kit self-jigs together for easy construction.
The Polly C is a 34-inch wingspan enlargement of the Polly B Old-Timer glider (also available from J&H Aerospace) that was tweaked and reformatted for modern tip-launching. It comes with a viscous dethermalizer (DT) but is ready to receive a remote DT. Construction is fast and straightforward, and the model is surprisingly forgiving in launch and glide trim.
Retro RC
Mark Freeland at Retro RC has just released the Minnow, a Science Olympiad Wright Stuff design. The double kit makes two airplanes and sells for $36.98. It is balsa and tissue, with no carbon fiber and no Mylar covering to worry about. It is designed to meet this year’s rules and has a wingspan of 45cm and a wing chord of 9cm. This airplane is also designed to give every competitor a good chance of achieving better than 1-minute flights, rather than being optimized for an expert builder who hopes to become a national champion.
The parts are accurately laser cut from quality wood. It comes with wood parts and Esaki tissue covering (white and some black) to make two complete airplanes, building jigs, a sanding stick, two propellers, rubber for four motors, O-rings, and rubber lubrication. The kit also contains a 10-page instruction manual with large photographs, full-size plans, and a suggested flight log template. It is almost guaranteed to fly right off the board with little trimming needed beyond adjusting the center of gravity by moving the wing location.
With stock propellers and a 1.5-gram, 3/32-inch rubber motor, it will fly for approximately 1:20; however, with the optional 9-inch Build-Your-Own-Prop kit (which sells for $12 and makes four propellers), you can greatly enhance the flight time by experimenting with the rubber strip width and the propeller pitch.
It is not yet ready for sale, but there will also be an electric Minnow for the middle school Super Capacitor Powered Wright Stuff event. It will have the same wing and stabilizer, with a much-lightened fuselage, and will be supplied with two complete power systems (5.0F Cap, motor, propeller, charging jack, a couple of spare propellers, and a charging pack). Retro RC is still working on the supply of power systems, so check its website for updates.
Retro RC has also introduced a laser-cut full kit of Lee Campbell’s Slow-Worm 432 (designed by Dave Platt and published in the October 1990 issue of Model Aviation). It has a 54-inch wingspan and, as the name would suggest, a 432 sq. in. wing area. The company’s plan is to also produce the 300 sq. in. version of the design at a later date.
This full 432 kit sells for $92.98. It builds fast and proved to be remarkably easy to trim. Although it was designed as an A Gas model, it is easily converted to fly Electric A/B. The electric conversion requires the nose to be extended by 2 inches to accommodate the lighter-weight electric motor. The Polyspan-covered prototype weighs approximately 500 grams, including a 3S 500 mAh battery pack. It took fourth place in Electric B at this year’s AMA Outdoor FF Nats.

Uben-Simple P-30
The Stick Figure from John McGrath at Laser-Cut Planes might be the easiest P-30 you’ll ever operate. If you hate blast tubes, reach rods, stuffing sticks, and blown motors stuck inside of fuselages, the Stick Figure is for you. You’ll swear you’re running an Indoor model.
Wind off the airplane, transfer the rubber




one end at a time to the hooks, set the DT, and you’re ready to launch. Fly the Stick Figure on six strands, four strands, or “slow burn” style with 3/32 x 4-inch strands.
Construction is designed for an intermediate modeler.
The kit includes a lightweight, tapered, carbon-fiber tube, laser-cut balsa, basswood, spruce, and plywood parts, a ball-bearing thrust bearing, a bailer-type freewheeler (that lets you swap propellers in a heartbeat), a fully adjustable front end, a Peck-Polymers propeller, and a simple viscous-timer DT system.
For full-on competition, a better DT system is suggested, and the kit includes a choice of wing pylons, one of which is precut for the Hummingbird Models Tiny Timer (not included). Photo-illustrated instructions explain how to build, trim, operate, and find thermal after thermal with this head-turning contest winner from Laser-Cut Planes. The introductory price of the full kit is $45.
GTS Free Flight
GTS Free Flight is a Los Angeles-based family venture of the Malkhasyans—father, George, and sons, Taron and Sevak. The models are thoughtfully designed for ease of building and maximum performance and are expertly laser-cut.
Two of their simpler designs caught my eye at this year’s FF Nats: the Cadet glider and GTS 12-inch glider. Both are hand-held Catapult Gliders with excellent performance. The Cadet is ideal for group builds with novices and kids, while the 12-inch glider is a nice step up into higher-performance aircraft.
SOURCES:
National Free Flight Society (NFFS)
www.freeflight.org
Retro RC
(248) 212-9666
www.retrorc.us.com
J&H Aerospace
www.jhaerospace.com
Laser-Cut Planes
johnmcgrath2@comcast.net
www.lasercutplanes.com
GTS Free Flight
gtsfreeflight@gmail.com





