Author: Gene Smith

Edition: Model Aviation - 2018/03
Page Numbers: 122, 123
Model Bristol Scout biplane on a wooden floor

World Wide Postal Competition

by Gene Smith
grwhiskey@brightok.net

It’s that time of year again. The grass is greening up and the temperatures are becoming more comfortable. It’s time to go fly some of those recently completed winter projects.

Perhaps there isn’t anyone in your area to fly with or with whom to share your flight times. The World Wide Postal Competition might be just the ticket! Go to the Endless Lift website for information about the 26th Annual World Wide Postal Competition. The link is listed in “Sources.”

The rules for a large variety of events are listed there. The events are primarily for Free Flight (FF) Sport models, but in many events, the only limitation is a certain wingspan. If you fly any FF at all, you probably have something that qualifies for one of the events. It’s all just for fun, so check it out and start recording some flight times.

While you are on the Endless Lift website, look at the winder counter. There is a great step-by-step tutorial showing you how to rig this simple system.

Gas One-Design

It’s not too late to start your Jasco Streak or Smarty for this year’s Gas One-Design event. The models are straightforward builds and go fast with a kit from BMJR Models.

Ted Allebone’s Martin Mauler

In my November 2017 column, I featured Mike Welshans’ Martin Mauler that was assembled from an Easy Built Models kit. Mike’s friend, Ted Allebone, also built one. Ted has completed test glides, but powered flights will need to be sorted out this spring. The aircraft’s empty weight is 30 grams.

Ted said it was slightly heavier than it needed to be, but mentioned that he tends to use harder stringers for

Model Bristol Scout biplane on a wooden floor
Bill Schmidt modeled the Bristol Scout, the first airplane to enter service for the British during WW I.
Orange Embryo free-flight model aircraft
Grant Carson has fun designing and building his own Embryo aircraft.
durability. He uses an 8-inch Peck-Polymers propeller in conjunction with a GizmoGeezer adjustable nose button and Nason propeller clutch.

Testing will begin with four strands of ⅛-inch rubber that are 20 inches long. The model is covered with Esaki tissue and has one coat of 50/50 thinned clear dope.

Crooked Cross

For Grant Carson, half the fun of modeling is designing his models. The Flying Aces Club (FAC) Embryo event is a great venue for creating your own model. Embryo models are a nice size with 40 square inches of wing area, build quickly, and typically fly well. The latest Embryo out of Grant’s “skunk works” is the Crooked Cross. The predecessor of this Embryo, which was much the same design, flew out of sight on its first official contest flight. At 19 grams, the Crooked Cross is even lighter.

The stabilizer layout is the same as the outer two panels of the wing—a simple design and building trick that was first used by the Chicago Aeronauts.

Grant was either lucky or, as I prefer to think, incredibly talented, because no ballast was required for the proper center of gravity. He carved the 8-inch propeller. The built-in wing incidence and downthrust were just right.

The test flights showed a slight tendency for a Dutch roll—a back-and-forth movement of the model’s tail. Grant added a small sub fin, which cured the Dutch roll.

Although wheel pants are in the spirit of Embryo, the three extra points, added once, are 0.8% of the possible 360 flight points, so Grant sometimes doesn’t bother adding them.

In test flights, he used a motor with two loops of 3/32-inch rubber, which provided plenty of power. Grant plans to try a single loop of 1/8-inch rubber to see if that is enough for long, gentle motor runs. Because Embryo models have to take off from a table, there still has to be enough power to get the model quickly into the air.

Tweet Scale Catapult Glider

George Voss built a Tweet Scale Catapult Glider from the Volaré Products kit. The finish is two coats of nitrate dope followed by spray-can white paint.

So far, 42 seconds is the model’s best flight. Any Catapult Glider that can do 45 seconds is capable of a longer thermal flight.

George has had so much fun with the Tweet that he is going to create some cut files for other possible Jet Cat models. He has a laser cutter and is already cutting parts for short kits of gas and rubber-powered FF models. Email George to see what kits he has to offer.

Bristol Baby

Bill Schmidt submitted pictures of his Bristol Baby—also called the Bristol Scout. It’s a compilation of many plans, with one going back to a 1950 Air Trails magazine.

The model has a 20-inch wingspan and weighs 2.05 ounces without its four strands of 1/8-inch motor rubber. The rigging wires are all silk thread that is secured with CA adhesive through .020 holes in the strut ends. Bill set the upper wing to +1° relative to the lower wing. The covering is Peck-Polymers white tissue and non-tautening nitrate. The trim is party store tissue and dope.

The Bristol Scout was the first airplane to enter service with the British in 1914 during World War I and start out unarmed. The British began throwing bricks at the Germans, but it quickly escalated to pistols, hand grenades, rifles, and finally, machine guns.

Notice the machine gun on the side of the fuselage. Bill wasn’t sure how that worked without shooting off the propeller, but it’s pictured in Aircraft of World War I, Vol. I.

FF on Facebook

I recently found another FF group on Facebook called CLUB—Peanut on the runway. I will leave the focus of the group for you to figure out. Just type the title into the search engine.

SOURCES:

National Free Flight Society (NFFS)
www.freeflight.org

FAC
www.flyingacesclub.com

26th Annual World Wide Postal Competition
www.endlesslift.com/26th-annual-world-wide-postal-competition-2017-2018-including-sky-bunny

Endless Lift Simple Winder Counter
www.endlesslift.com/a-simple-winder-counter

BMJR Models
(321) 537-1159
www.bmjrmodels.com

GizmoGeezer
(306) 955-1620
www.gizmogeezer.com

Easy Built Models
(334) 358-5184
www.easybuiltmodels.com

George Voss
gavoss@swbell.net

Volaré Products
(269) 339-9795
www.volareproducts.com

CLUB—Peanut on the runway (Facebook closed group)
www.facebook.com/groups/1489054624459718

White Tweet model aircraft on a wooden table
George Voss has racked up some decent flights with his Tweet from a Volaré Products kit.
Blue Martin Mauler model aircraft on grass
Ted Allebone’s Martin Mauler, from an Easy Built Models laser-cut kit, rests between flights.