One-Design for 2017
by Gene Smith
grwhiskey@brightok.net
The dual One-Design models for next year’s Nats will be the Zingo and the Witch Hawk. The Zingo is eligible for the Early FAI event. That category might be flown at the 2017 Nats. If so, the Zingo could fly in two events. Plans for both aircraft are available from the National Free Flight Society (NFFS) plans service.
As of this writing, the rules on the NFFS website specify a non-Schneurle .15 engine for the Witch Hawk 500, but this should change to allow a Nostalgia-legal .19. Check the NFFS website to be sure before building your model.
BMJR will offer laser-cut kits for both models. I purchased a Witch Hawk kit from Brian Malin at this year’s Nats. I am also building a short kit of the Witch Hawk from Bob Holman. I hope to have a picture of the finished models for my January 2017 column.
Homegrown Television Productions
If you have seen any of Alan Abriss’ model aviation videos, you know they are informative and of high quality. This year’s Flying Aces Club (FAC) Nats video is no exception. Check out Alan’s website for ordering information.


Jimmie Allen Special
Bill Schmidt says the Jimmie Allen Special is just that—special! He has built two of them. At a club outing this past March, Bill flew the old yellow model he built 11 years ago. It climbs at approximately 60° and goes quite high. The glide is very good.
It was nearly lost on the second flight when the rubber band wasn’t deployed over the dethermalizer fuse. Thank goodness for Jeff Englert, who saved the day by spotting the model as it came down.
Bill gets better flights out of these Jimmie Allen Specials than he ever did with a Flying Aces Moth. The fuselages are covered with dyed Polyspan; the rest is Japanese tissue and non-tautening nitrate. He uses two loops of ⅛ x 19-inch braided rubber. The 7-inch propellers are carved using the Bill McCombs-modified X-block design, which Bill likes and thinks might contribute to the model’s outstanding performance. Each airplane weighs 1 ounce with the motor installed. A full laser-cut kit for this 20-inch wingspan model is available from Easy Built Models. A laser-cut short kit is available from Volaré Products.
William McCombs’ paperback book, Making Scale Model Airplanes Fly: For Sport or Contests, has a wealth of information, including the modified X-block propeller. The booklet is available through Amazon. I have had my copy for many years and it has proven invaluable.
WESTFAC One-Design
The One-Design theme for the 2017 Western Region Flying Aces Club (WESTFAC) meet is aircraft from the Spanish Civil War. The first to build a model for the event was David Wagner with his beautiful Lockheed Model 9 Orion. The Republican Air Force acquired 13 Model 9 Orions and used them as transports.
David’s Orion was built from an Easy Built Models kit. It spans 24 inches and weighs 34 grams. The front end uses a GizmoGeezer with a 9.5-inch propeller cut down to 9 inches.
The beautiful finish is airbrushed Tamiya acrylic paint over white Japanese tissue. Power will be provided by two loops of ⅛-inch rubber.
David gives his models a light spray of Tamiya spray paint on top of white Japanese tissue, from which he gets a powdery effect. Colored areas (in this case, the red wing and fuselage bands) are masked off before spraying the main background colors so that colors are not overlayered. The white tissue areas are left unpainted, which works better when there is a higher contrast background color such as what is on the fuselage.
David wants a translucent effect. In the past, he applied the paint until it was opaque. He doesn’t think the translucent finish saves that much weight, but it is a visual acknowledgement of the model’s structure.
For the side passenger windows, he glued on thin, clear, plastic sheet, and then covered it with tissue. After spraying the color and applying a final light dust coat of clear Krylon, David cut the tissue over the plastic sheet to reveal the windows.
Any loose edges were sealed with glue stick. The glue stick adheres the tissue to the plastic and cleans up easily with a wet Q-tip. See the Spanish Civil War page on the WESTFAC website for a link to eligible aircraft. Some short kits for eligible aircraft are also available from P.T. Aviation.

E-20
The E-20 event is growing in popularity because of its low cost and the small size of the models. Bob Stalick’s club, the Willamette Modelers Club in Oregon, has been instrumental in promoting the E-20 event.
A preassembled motor, propeller, battery, and motor-run timer are available through the club’s website. You can also find E-20 tips and the event rules on the site. Rules can also be found on the NFFS website.
Dohrman Crawford purchased one of the power packages and designed his Cattywampus Canard for the event. All of the canards that Dohrman has built have flown well, and have had an impressive climb. The model weighs 35 grams, ready to fly.
It proved harder to hit the 30-gram minimum weight than Dohrman thought. He weighed every component during the build, but was still slightly above the target weight. The tissue strips, visible on the wings, stiffen them while adding little extra weight.
The graphics are by Callie Graphics, a company that Dohrman and many others recommend. He has completed his test flights and is quite pleased with the model’s performance.
Two kits for E-20 models are available from BMJR Models.
This canard E-20 was designed and built by Dohrman Crawford. Crawford photo.
Howard Littman’s Bostillation
Howard Littman is now kitting a Bostonian he calls the Bostillation. The prototype model weighs 15 grams, comes with a 6-inch Peck-Polymers propeller, and has been flown on both a single loop of ⅛-inch Tan Sport rubber roughly twice the hook-to-peg length, and a longer ³⁄₃₂-inch motor. The production version will have shorter fins.
Howard’s prototype flew right off the board. The model also qualifies for the Embryo event—simply add wheel pants and an exhaust stack for the bonus points.

Howard Littman borrowed the three-fin concept from the Lockheed Constellation for his new Bostonian model, named the Bostillation. Littman photo.
Flying Models
The Flying Models Plans Store is up and running again. Check out the Flying Models website.
SOURCES:
Howard Littman Model Aircraft
howard@hjlmodels.com
www.hjlmodels.com
BMJR Models
(321) 537-1159
www.bmjrrmodels.com
Bob Holman Plans
(909) 885-3959
http://bhplans.com
Homegrown Television Productions
contact@homegrowntv.com
www.homegrowntv.com
Easy Built Models
(334) 358-5184
www.easybuiltmodels.com
Volaré Products
(269) 339-9795
WESTFAC
www.westernfac.com
GizmoGeezer
mail@gizmogeezer.com
www.gizmoge ezer.com
P.T. Aviation
www.ptaviationmodels.com
Willamette Modelers Club
www.willamettemodelersclub.weebly.com
Callie Graphics
info@callie-graphics.com
www.callie-graphics.com/airplanes.php
Flying Models Plans Store
http://store.flying-models.com/catalog





