Award-Winning Aircraft Finishes
Tips to take your model to the next level
By Dan Grotzinger

After seeing magazine coverage of the Best of Show and Best Finish winners at The Toledo Show: R/C Model Expo, held in Toledo, Ohio, when I was a kid, I usually felt a sense of awe and respect for what they represented. Gradually, a thought germinated in my mind: maybe, someday, I could do that.
This is a good place to clarify an important issue. You don’t build and paint an award-winning model to win a prize—you do it for yourself. We all appreciate positive feedback, but if I were alone on an island, I would still do the same work. Excellence of workmanship is a craftsman’s reward.
I grew up in the hobby during the 1960s on Control Line (CL) “Stunters,” that featured silk and dope finishes. There was no CA glue, no MonoKote, and no ARFs. You did the heavy lifting or bought someone else’s airplane.
Some of the best CL Stunt (Precision Aerobatics) aircraft were hand-rubbed (sanded with fine-grit sandpaper and then rubbed with polishing compound), because Stunt has a finishing component to its scoring.
In those days, AeroGloss was the gold standard. Your airplane could have a beautiful satin finish in two or three weeks by using a brush and no buffing. Butyrate dope often required buffing because it did not flow out and shine as well. AeroGloss was excellent for brushed-in repairs that became invisible without the need to paint an entire area.
Unfortunately, AeroGloss went through a progression of formula changes that rendered it inferior. Except for clear, which I still use to attach silk and tissue, it is no longer available.
My first hand-rubbed finish was with Sig Manufacturing dope in 1987. The dope was tricky to use because freshly applied coats would soften already sanded layers, reintroducing surface imperfections that required additional coats of an already heavy product.
Using clear nitrate in the base layers’ buildup somewhat alleviated this problem. Sig dope tends to shrink and pulls up at tail fillets. Much of the paint applied to the fillets must be sanded off until the final coat to reduce paint buildup and solve shrinking.
Next, I tried K&B epoxy and was pleased. The biggest problem with it was the slow cure and resulting tendency to attract dust. Sometimes it would attain an “orange peel” (a texture that resembles the skin of an orange) or “fisheye” (small circular, crater-like openings) appearance, a trait that seems common to epoxy paints. These traits make rubbing an attractive option.
I’ve tried water and particulate filters in the spray system, as well as surface preparations suggested by professionals, with limited success. The best prevention beyond that is applying thin, wet coats. After I had used it twice, K&B went off the market.
The next product that I tried was Chevron Perfect Paint. I had excellent results on several warbirds using the military flats. That product is also no longer available. Since then, I’ve used several others, including Rust-Oleum and automotive products—all with mixed results.
Each product has a learning curve with various pros and cons. There is no perfect paint. As with all things, you must work with each product’s strengths. Imagine my surprise and delight when Klass Kote epoxy appeared at the Toledo Show and was advertised to be interchangeable with K&B and HobbyPoxy paint components. I bought some and used it on a scratch-built Senior Skylark Twin with excellent results.
Because rib structure is a prominent feature of the Skylark/Falcon family of wings (no sheeting), it is not advised to rub out the finish. A consistent rubbing procedure would cut small valleys into the finish at the edges of the ribs, risking sand-through. Not rubbing the ribs would create inconsistent areas of polish and shine.
Careful application of a thin top coat resulted in a satisfactory final finish. A couple of unsightly dirt specks were spot sanded and polished without being noticeable.
How did I end up at the Toledo Show with a Best Finish winner? Everything came together. I had been collecting, building, and painting vintage airplanes when I discovered the Vintage RC Society (VRCS). The group has a Concours competition category, which encourages building vintage models “as they were in the day.” In 2009, VRCS was awarded its own category at Toledo. Competing against the best at a national level forced me to improve.
Throughout the years, the passing of many modeling friends impressed upon me that the time we have to do the things we wish might be limited. In 2013, I had problems that led to surgery, which convinced me even more.
Although I only competed in Pattern (RC Aerobatics) for one year, I love aerobatics and practice like a competitor. I saw an old Mach 1 Pattern airplane for sale at a swap meet. I admired its lines and proportions in three dimensions, but it seemed too heavy. (I once had a kit, but hadn’t seen one built.)
Two rows later, I found an original Midwest Products Mach 1 kit for sale. I have had several foam core wing kits and let them all go because of my perceptions about weight and adhesive issues.
The seller of this kit gave me some useful information on bonding wing skins, which I will explain later. I saw the use of Klass Kote on a fully sheeted foam core wing as the ticket to the best finish I had done. I could sand and buff to my heart’s content with no ribs to worry about. Three days later, I was building. Passion, experience, urgency, and circumstance had intersected.
I am not a professional with the requisite training, information, facilities, and equipment. If I can do this, with patience and desire, so can any modeler. I’ll share with you what I’ve learned from my mistakes. Are you ready? Let’s jump in!


not be visible until the final finishing. Use Testors cement or something similar, and then immediately wipe the excess off of the surface so you won’t have as much to sand.
I pin the sheets to force them tightly together and tape them to keep the joint flush. I do this on the building surface over waxed paper. Sand the skins before bonding them to the foam cores. Companies such as Balsa USA supply wing-width skins, eliminating this chore.
Most of the strength is in the skins, so if the grain is bad or the wood is too soft, replace it. Grain irregularities can be hard to see and judge, but can affect your finish. More paint will correct this, but it adds weight. Grain irregularities pose the biggest problem on the large surface of a wing, which will be similar to a mirror when you are done.
At night, when I think I am done sanding, I turn out the lights and leave a small television on. I sit roughly 12 feet away and hold the wing between the TV and myself so that the wing reflects light to me on a tangent. Different angles with varying amounts of light will show every variation and flaw that you missed in normal light. You can then lightly sand with 320-grit sandpaper.
This same sighting technique, sometimes referred to as candling, can be used in normal light to sand out each layer of paint. If you wait until the final coat to make these little corrections, the job will be harder and less effective.
Setting Up
An 8-gallon 125 psi compressor, a DeVilbiss touch-up paint gun, a Badger airbrush, and a carbon-filter breathing mask are my essential equipment. Slow-drying epoxy paint can be applied with an airbrush.
I use a stand that acts as a rotisserie by mounting it onto the model’s motor mounts. I usually have a checkerboard pattern on the bottom of the wing so that the top and bottom do not need to be sprayed at the same time.
If you need to spray both at once, standoffs can be mounted in the servo openings of the wings and in the openings for the wing bolts. You spray the bottom first, turn the wing over, setting it on the standoffs, and then spray the top. When spraying the bottom, place the wing on clean waxed paper to avoid carrying dust to the yet-to-be-sprayed top surface.
Applicable Building Tips
This is not a building article, but a few tips bear mentioning because a great finish is hard to accomplish over flaws. Use a metal straightedge and a sanding block to true-up as many joints as possible, trying to avoid putty.
Many glues can be sanded when the joint is 90° to the surface. A feathered joint, such as D-tube sheeting that wraps over the leading edge instead of butting against it, is another matter if the glue used is epoxy or CA. For this reason, I use Testors solvent-type wood cement in these situations. The glue and balsa will sand off at the same rate, leaving a clean joint instead of an unsightly hump.
The Mach 1 has 3-inch sheets that can be glued together for wing skins. If you use CA adhesive on your aircraft, you will have to sand too much to create a clean joint, leaving a valley that might


Bonding Wing Skins
The Mach 1’s skins were bonded with Gorilla Glue. It does not debond over time or in the sun as contact cement does, and will not add weight as epoxy does. When properly done, there will be no messy excess.
Apply the glue to the wood skins, spreading it to a thin film with a credit card. If the wood “fuzzes up” and looks dry, you took too much glue off. Spread a little more. Using a spray-mist bottle, lightly wet the foam cores and rub the moisture around with a clean hand. This creates a surface tension that you will feel.
Glue the upper and lower skins to the cores at the same time, mounting them back in their foam carriers or castoffs. Because the wet wood expands, a warp can be introduced when doing one side at a time.
I used a thick glass table for this assembly, but any flat surface will work. The top of the assembly must also have a flat surface, and it needs to be weighted. A fair amount of weight that is equally distributed won’t crush or compress the cores.
Install straight pins through the skins into the foam in a few places to prevent creeping while curing. When done, there will be little excess glue pushed out. There also will be no humps or irregularities and it will be lightweight and strong. The remainder of the wing assembly will be a breeze and you will love the result.
Fiberglassing
The Mach 1 was fiberglassed using Sig .5-ounce and .7-ounce cloth. The heavier cloth is easier to handle, fill, and sand, but adds more weight. It was applied around the nose and wing fillets for durability, and on the top of the wing for a better surface texture. The lighter cloth was used on the remainder of the airplane. I used Zap Z-Poxy finishing resin for this project.
At this point you have a controversy and a decision to make. Some modelers thin the mixed resin 50/50 with denatured alcohol and brush it on like silking a wing with silk and dope. Some feel this softens the resulting finish, so they apply the resin using a squeegee and the toilet paper-blotting method. I prefer the thinning method because it is quicker, easier, neater, and lighter. I’m careful with my airplanes, so I rarely dent them.
This method quickly produces a good, lightweight surface. If you are prone to accidents, you might prefer the other method. Sometimes I apply a coat of clear dope to the wood before fiberglassing. This seals the wood and it seems to require less epoxy.
A dry fiberglass cloth is placed over the wood with roughly an inch of overhang past the desired fiberglassing area. The resin is brushed in, starting at the center and stroking outward in all directions. This prevents the material from bunching, rolling, and sliding. After it cures, the excess will sand off easily with 220-grit sandpaper.
Edges are easy, but end on a flat area that will easily feather out with sandpaper. The next piece can slightly overlap the first area, and it will also feather easily when cured. This lets you use pieces as big or as small as you want and the seams will disappear. I use fiberglass cloth on solid wood surfaces, no matter what paint I use or the size of the airplane.
In a rebuild or refinish, the old paint can be stripped with thinner—leaving your fiberglassed surface like new. The exception is epoxy, which must be sanded off.
After everything is covered, brush on a second coat of resin. It takes approximately six hours to be sandable. Start with 220-grit and end with 320-grit sandpaper. I take off the resin down to the surface of the cloth, so only the weave is filled.
You can feel when you get to this point and the sound of the sandpaper will become scratchier. Depending on the wood grain, the weight of cloth used, the consistency of your resin, and your brushing technique, you might be done or you could have a few pinholes and open grain. You can apply a third thin coat of resin with a lint-free cloth, or depend on your primer to fill these
problems. I’ve done it both ways.
If you have a sand-through in the cloth, you might want to recoat that spot unless you are using epoxy primer (in which case it makes little difference). Some patience with the fiberglassing and sanding will give you a beautiful, lightweight base for your paint. The design weight of the Mach 1 is 8½ pounds, but mine topped 7¾ pounds.
Epoxy Paint Pros and Cons
Epoxy finishes can often be completed with only two coats of primer and two coats of color. Subsequent coats do not soften or alter previous coats. There is little shrinkage to cause the sheeting to buckle or distort and pull paint up from tail fillets.
Masking will only pull up paint if it is too thin and applied to an unclean surface. It will not fade, crack, or age, and is fuel and cleaner resistant. It is cured to sand and handle in 24 hours, and reaches “sword hardness” in four days. Epoxy is the perfect paint for buffing because it does not need to gas out.
Disadvantages to epoxy are that it is more prone to need buffing, is more expensive than some other finishes, and is messier than many products. It must be poured from container to container, and then into the paint gun to ensure complete mixing.
The overspray does not dry in the air as dope does, so it bonds wet to anything it lands on. Because of its viscosity, it picks up more dust in both the spraying and curing process than most other paints do.
There is a waiting or induction period after mixing that allows the chemical process to get up to speed. If you don’t mix enough, you are stuck and cannot complete an area. You might tend to overmix and waste epoxy. If you have excess, store it in a refrigerator for a few days and use it for the next coat.
Epoxy paint is heavier than many finishes, but applying it with a good technique helps. It tends to develop an orange peel texture, but that can be minimized with proper thinning, clean air, and clean surfaces. If you intend to sand and buff, a mild orange peel appearance becomes a nonissue.
Color and Geometry
You can apply a perfect finish and still end up with an unattractive model if you don’t plan your colors and geometry well. This does not apply to scale models.
When I first got into the hobby, I read an article in American Modeler that included some basic principles to use when planning a finish. The first is to use at least two main colors, a dark and a light, for contrast. This is important for more

than appearance; it gives good in-flight visibility.
The dark color should be approximately ⅓ to ¼ of your surface area minus trim, and the light color should be the remaining ¾ to ⅔ of the surface area. A ⅛- to ¼-inch wide line of either white or black to separate the two main colors, depending on the overall scheme used, can add life to your finish.
These color-separation lines can enhance the airplane’s geometry. A nearly horizontal line from the spinner to the rudder makes a great accent. A line from wingtip to wingtip, near the high point of the airfoil or on the spar, also is visually pleasing. These lines can be curved or diverted at the root or wingtip for enhancement.
Sometimes the two main colors touch and the trim line can run parallel to, but away from, their border. This was the crux of the American Modeler article and it has served me well with many variations and modifications.
The Mach 1’s finish geometry traces its lineage back to that article. I consider this the only truly unique paint scheme that I ever devised. It was first developed for a Veco Chief in 1964. The dark color was Stinson green, and the lighter color was that same green lightened roughly 1:1 with white, creating a two-tone final finish.
On this model, the separation color was black—not very original. I chose to put a yellow stripe slanted roughly 40° across the wing chord, near the wingtip. Then it seemed that two stripes of contrasting color would be even better. How about gray or a neutral? I then got a real inspiration. How about flipping the two-tone beyond the chordwise stripes? Wow, that looks good!
I’ve used this two-tone scheme on eight or nine airplanes in red, blue, green, maroon, and purple. The beauty of the yellow and gray stripes is that they work with many other colors.
There have been airplanes that used this geometry, but not as two-tones, such as red and yellow and red and lavender. I have painted airplanes with only one main color that still incorporate the wing chord and separator stripes. Sometimes the wing chord stripes became a checkered stripe or merely a silver stripe with a black and red border. I’ve almost worn this geometry out, but the variations keep working.
Please refer to the picture of my recently rebuilt Dirty Birdy for a simple, but attractive, three-color metallic finish. This started out with black as the dominant color, red as the secondary, and silver as the trim.

The red is a simple wedge pointing into the fuselage on both the wing and the stabilizer. The point is located forward of the midpoint of the wing chord and the forward edge of the red does not sweep as much as the rear edge sweeps. This results in a balanced, pleasing effect on the swept wing. I planned to use a simple ¼-inch silver trim stripe, but decided to broaden the silver to twice its width as it swept to the wingtips. This simple change brought the wing and tail to life.
The Dirty Birdy has a low fuselage profile. I decided to make the dominant color there red instead of black for visibility, and to make the secondary color at the nose silver.
Black became the trim color on the fuselage. This layout engages the eye and brings the model to life. Black, red, and silver are simple, similar-tone metallic colors, but they look good in the air. The red pops in vertical maneuvers and the silver nose stands out in level flight.
Note that on both the Mach 1 and the Dirty Birdy, the main theme is not extended to the fin. I used to do that, but I decided that it looks too busy.
Choose interesting, vibrant colors. Red, white, and blue are nice, but have been overdone on models. Some great color combinations are lemon yellow with black trim, pink and black, yellow and purple, orange and blue, dark blue and light green or the reverse, and lavender and turquoise.
Keep your eyes open and you will get ideas. I first saw powder blue, burnt orange, and Cub Yellow on a paper at a mall. Those colors stuck with me and appeared on three airplanes before being incorporated into the Mach 1.
—Dan Grotzinger
spitfirefighter@hotmail.com
SOURCES:
The Toledo Show: R/C Model Expo
www.toledoshow.com
Vintage RC Society
www.vintagercsociety.org







