Author: Gene Smith

Edition: Model Aviation - 2016/03
Page Numbers: 125, 126
Two model Stout 2-AT airplanes in a vehicle trunk.

Goodbye to the PFFT

by Gene Smith
grwhiskey@brightok.net

The year 2015 marked the last year of the Pensacola Free Flight Team (PFFT). After decades of responsible use of a U.S. Navy-owned field, the Navy has terminated the club’s use of the site for “security reasons.” Having flown at the site, I can say that the decision is a loss for the community and for the concept of common sense.

On a brighter note, George White, editor of the PFFT newsletter, compiled a gold mine of useful hints and tips of his own and from others. Before closing the PFFT website, George transferred the database to Volaré Products and the National Free Flight Society (NFFS). If you are new to the hobby, or just want to up your game, check out this valuable resource. Thank you, George, for this gift to the Free Flight (FF) community.

Durham Mystery Plane

The Flying Aces Club (FAC) Embryo event is popular because the models are relatively simple to build and are good performers. The maximum wingspan is 16 inches and the maximum wing area is 40 square inches. Bonus points are awarded if the model sports wheel pants, motor “exhausts,” and has either an elevated cabin or a cockpit with a windshield.

Two model Stout 2-AT airplanes in a vehicle trunk.
Check out these two good-looking Stout 2-ATs by Mike Welshans and Jack Moses. Welshans photo.

Nothing says you can’t fly a smaller airplane, hence the Durham Mystery Plane. Designed by Tom Nallen, the model meets the requirements for an Embryo, but only spans 13 inches. It’s cute as a bug and is easy to store and transport. A laser-cut short kit is available from Volaré Products.

A man launching a model airplane in a field.
Mike Welshans is pointing the way with this perfect launch of his Stout 2-AT.

FAC Outdoor Championships

Your mission, should you decide to accept it, is to build and fly a Stout 2-AT Dime Scale model for the 2016 FAC Outdoor Championships to be held in Muncie, Indiana, on September 22-23. If you can’t make it to the contest, at least fly your model at your local field.

This design has all the hallmarks of a great flier. A short kit is available from Volaré Products. For information about the FAC, including contest dates and rules, check out the FAC website. There may be an FAC squadron in your area.

Cessna 195

When Tom Derber divested himself of his fleet of FF models, Bill Schmidt picked up his Cessna 195. Tom had built this fabulous rendition of the aircraft more than 10 years ago, using his own plans.

It spans 23 inches and weighs 45 grams. It originally had an 8-inch Peck-Polymers propeller installed and was powered by four strands of ³⁄₃₂-inch Tan II rubber. The rubber was so old it came

George Bredehoft holding a yellow model airplane.
George Bredehoft poses proudly with his Durham Mystery Plane Embryo at the AMA Outdoor FF Nats last summer.

out like a dried worm!

Bill did a little work on the model, such as detailing the tail wheel and replacing the blue tissue trim on the front nose cowling. A close look will show a different color on the forward part. The cowl had been covered with one piece of tissue resulting in some unsightly overlaps that distracted from its appearance. Bill removed the tissue from the cowl and covered it with narrow strips of wet, blue domestic tissue, butt-joined side by side running fore and aft.

Bill said that this method is fast and easy and results in a great, finished look. He advised using domestic tissue because its colors are deeper and less prone to fading than Japanese tissue.

Bill first applied two coats of nitrate dope to the bare wood. The tissue strips were tapered to allow for the smaller diameter of the front of the cowl. He laid the tissue in place then floated it

Model Cessna 195 with its cowling and propeller.
The Cessna 195’s cowling conceals a Jacobs radial engine that produces up to 300 hp. Photo by Bill Schmidt.

into position with nitrate thinner. A little saliva on the tip of his finger allowed him to push the tissue to make fine adjustments. If you haven’t tried this trick before, you will be amazed at how well it works!

Yellow and orange Skokie model airplane on a workbench.
Jerry Klingamon is justly proud of his great-flying Skokie, built from an Easy Built Models kit. Klingamon photo.

Skokie for the One-Design Event

Jerry Klingamon sent along a photo and some information on his Skokie, which he built from the Easy Built Models kit for his club’s One Design event. He reported that the model flies wonderfully. The center of gravity was spot-on, with no balance weight required. The only trimming it needed was a little up-stabilizer trim. The model has been saved by its dethermalizer on several flights.

Jerry carved the 10-inch propeller and turned the wheels out of super-lightweight balsa. The gray tires are reminiscent of those used during the 1930s. The fuselage decals are the light tissue type provided in Easy Built kits. Jerry’s model uses two loops of ³⁄₁₆-inch rubber wound 800 turns to 9 inch-ounces of torque. Thanks for sharing.

Using Kicker

I received a nice note from Frank Pisano regarding Ken Achee’s Kicker Dripper. Frank stopped spraying kicker quite a while back when he realized he was spraying half the model and the workbench. His solution was simply unscrewing the cap and using the tube in the bottle of kicker as an applicator.

To prevent kicker spilling from the loose cap, Frank cut out a square of pink insulation foam used for houses and made a round hole in the center to accommodate the bottle. That prevented it from tipping over. You do have to remember to tighten the cap after the gluing session because the kicker will evaporate.

Thanks, Frank.

Salvaging Old Decals

Alan Wolcott wrote to advise me of another way to salvage old kit decals. Microscale Industries makes a product called Liquid Decal Film. It can be used to make your own decals by brushing over an image you have printed on decal paper, or it can keep old decals from cracking.

It is probably stocked in hobby shops that cater to plastic model kit builders or model railroad hobbyists. It is also available online directly from Microscale.

SOURCES:

Volaré Products
(269) 339-9795
www.volareproducts.com

NFFS
www.freeflight.org

FAC
www.flyingacesclub.com

Easy Built Models
(334) 358-5184
www.easybuiltmodels.com

Microscale Industries
(714) 593-1422
www.microscale.com