Edition: Model Aviation - 2002/05
Page Numbers: 129, 130, 131

FREE FLIGHT SPORT and SCALE

Fernando Ramos, 19361 Mesa Dr., Villa Park CA 92861; E-mail: fkramos@att.net

I'VE RECEIVED numerous E-mail messages from people who confess to having the same modeling habit I have: starting many different models before finishing one. Sometimes I get criticism from my modeling friends; their comment is usually "I can't build this way." My remark to them is, "I will compare my output to yours anytime!"

I am in the process of finishing many of the models I framed sometime ago. It is great fun to take several new models out for test-flying. After all, isn't the whole idea to have fun at what you are doing modeling-wise? I happen to be one who loves to frame models.

Those of you who have read my column through the years probably know that I like to laminate basswood for trailing-edge wingtips (as a single unit), rudders, stabilizers, bulkheads, etc. You probably also know that I try to make any model easy and quick to produce.

I was building a World War I biplane with roughly an 18-inch span for rubber power. I was ready to start on the wings, laminating the tips first, then the thought struck me: Why not try using 1/16-inch-outside-diameter (OD) aluminum tubing instead?

I made a poster-board template of the wingtip. (I think I have mentioned this before, but art-supply stores have a variety of poster boards of varying thicknesses that make wonderful templates for laminating.) I bent the aluminum tube around the template, pulling it around rather than just bending it.

The results were gratifying. There were no flat spots, and the tip looked great. I installed it using five-minute epoxy sparingly against the balsa wood. I was going to make a separate wingtip using basswood and compare the weight, but I didn't. The aluminum tube doesn't weight much.

I thought that if the tubing worked this great on the wingtips, why not try the rudder and stabilizer the same way? I made the respective templates and formed the tubing around them as I did for the wingtip, and the results were just as good.

However, there is one caveat: the radius of the tubing cannot be too small, or it will flatten or kink. You certainly don't want that!

Another use I have come up with for aluminum tubing is to make control horns for my biplane. The horns are quite small—at 3/4-inch = 1-foot scale—but they have to be strong enough for the rigging required, so I decided to make one from 1/16-inch OD tubing.

I cut the tubing the exact length needed, then I flattened the ends. The way I did this is what makes it look realistic. Rather than just squeezing the end, I stuck one end of the tubing in the throat of a pair of needle-nose pliers. I squeezed gently, and only the end was flattened, leaving a triangular cross-section when viewed from the front. I drilled a small hole at each end for the rigging, then I epoxied them onto the structures.

When it came to covering the wings and tail, the results looked realistic. I made my frames for the tail and preshrunk the tissue before attaching the structures to it; this ensures a warp-free surface.

I maintain that the overall weight differential is too slight to be a consideration. Try this on your next model.

I have to add a couple of new adhesives to the list I compiled in a previous column.

One is Quick Grab®: a fast-setting, clear glue that will stick in 40 seconds. It will bond to almost every material, including some plastics and polystyrene. This adhesive cannot be damaged by freezing.

I have been using Quick Grab® to hold down brass fuel tanks I have made. Because it is not a silicone (although it looks like it), it can be painted. It can be used as a contact cement. The cost is $2.50 for a 1.5-fluid-ounce tube.

The other product is Quick-Stik epoxy putty, which is made by the same company that makes Quick Grab®. It comes in a plastic tube and is a solid 3/4- x 8-inch-long bar. You slice off the amount you think you will need, then knead it until it becomes uniform in color. It is actually two parts in one stick. It will harden in only 20 minutes and becomes like steel. Quick-Stik can withstand high temperatures and will work underwater.

I have used similar materials, but I was impressed with Quick-Stik because it is Kevlar®-reinforced.

I don't know how much this epoxy putty is. You can obtain further information from Quick Grab, Inc., in care of Dennis Marcotte Jr., 242 Neck Rd., Haverhill MA 01835; Tel.: (978) 374-0094. The Web site is www.quickgrab.com.

Bending wire can be a pain for some—especially when the diameter is larger than 1/16 inch. As do most modelers, I use a wire bender from 3/32 inch up in size. I mark a scrap piece of wire where it needs to be bent, then I can determine where the wire has to be placed on the bender platform to get the curve exactly where it needs to be. Then I make a permanent mark on the platform so that repeated bends will be accurate.

However, sometimes when it comes time to make the bend which will be the axle, it isn't on the same plane as the rest of the bends. Many modelers rely on the "eyeball" method to keep all bends flat, but I use a simple idea to keep them on the same plane.

If you are not familiar with line levels, masons use them by stretching a string between a couple of points. The line level is small, light, and hooks onto the string. This way the masons can determine the obvious.

I place this device on the end of the wire I am bending. Before I make the bend, I check to see that the wire is level.

Simple, eh? The level is so light that it does not cause the wire to bend.

Few of us consider built-in stresses—such as having a bit of a bind on, say, a longeron—while building a model. One reason why I soak longerons overnight before pinning them down onto a plan is to help eliminate stresses. I can't help but think that these are caused after covering because of some of these built-in strains.

Wings are probably the most likely places for these built-in stresses, and I have an approach to eliminating them. While a wing panel is pinned down waiting for the glue to dry, I spray the entire thing with Windex® window cleaner.

Why? It contains ammonia, and we use ammonia to soak balsa to make the wood more pliable or flexible. I spray an even, wet coat over the entire wing, but I do not try to saturate the wood.

One situation turned out to be a good example of how well this works. I was preparing to make the interplane struts on my biplane. I made a fixture securing the upper wing center-section. I plugged in the lower wing panels, followed by the upper ones.

The fuselage was aligned with right-angle lines I had drawn on my workbench, and the fuselage struts were glued on. When I removed the pins, the wings were practically perfect; the panels had not pulled in any direction.

I don't usually do the tail surfaces since I use pre-shrunk tissue on frames for these structures.

I have mentioned before how I make interplane struts, but I have modified the method somewhat, so a review is in order. Following is what I do for my diesel-powered biplanes.

While building the wing panels, I very carefully mark where the interplane struts are to be mounted. I glue on small balsa blocks that are large enough to accommodate anchor points for rigging.

When the glue has dried, I drill 1/8-inch holes, using a drill press, at the exact point that the struts will attach. Then I cyanoacrylate-glue (CyA) aluminum tubing into the holes. After the wing is attached to the fuselage and propped up with the proper dihedral and incidence, I am ready for the next step.

This is where I have made a change. I purchased some 1/8-inch-diameter aluminum wire (which can be found where brass and aluminum tubing is displayed in model shops). I slid the aluminum wire from the top wing down into the bottom wing through the tubing, inserted in the balsa blocks.

I used to use piano wire, but there was no flex. The aluminum wire bends easily and it doesn't matter if the interplanes aren't vertical to each other, just bend them to suit you.

I measured the distance between the two wing panels so I could cut the wood accurately. I scored the inside surface of each half of the strut for the wire to fit into before gluing the two pieces together. Then I glued the wood for the struts in place. Whatever you do, don't use CyA; you don't want to get any where the wire goes into the tubing. I certainly wouldn't want to be around the person who does this!

Don't forget to label the struts properly. I wrap small pieces of tape around the wire, then I mark them with, for example, "right rear—top," "right front—top," etc. Top and bottom matters because of the dihedral angles created by the airfoil.

I borrowed a new book entitled Drawing the Line: The Art of Aviation. If you are interested in the early history of aviation, the book is for you. It is large, with approximately 400 pages, and has many photographs and some three-views.

Not surprisingly, Sopwith, Avro, Bristol, and Short had the majority of airplanes flying before World War I. I would love to build a Free Flight model of the Bristol Boxkite.

This tome is not cheap at $59.95, but it is printed on high-quality paper. It can be ordered from Schiffer Publishing Ltd., 4880 Lower Valley Rd., Atglen PA 19310 Tel: (610) 593-2002 Website: www.schifferbooks.com

Thanks for all the E-mail messages and terrific newsletters. MS

Transcribed from original scans by AI. Minor OCR errors may remain.