Free Flight: Duration
WHICH GLUE TO use? Growing up, the choice was easy . . . Ambroid was the stuff my father used, so I used it too. Later I began using cyanoacrylates (CyAs) for field repairs and aliphatic resin (Titebond) for general construction. If I was in a hurry, I'd opt for CyA for construction. But I really liked Titebond. It was cheap, easy to use, and safe. About 15 years ago, I built two A-1 glider wings-one using CyA, and the other, Titebond. The unfinished panels were stored away in a cardboard box, which, it turned out, happened to be under a leak in my workshop roof. When I discovered the leak, the box was full of water. The Titebond wing had rekitted itself, with all the parts floating around loose. The CyA wing was soggy but still intact. I weighted it down on a flat surface and let it air dry; it was fine.
Free Flight: Duration
COUPE PLANS: A few months back this column featured some photos and a description of Eric Johnson's potent new Dream Catcher Coupe. Now Eric is offering full-sized plans of the model. The plans for the 54-inch-span model are quite detailed and even include an isometric sketch of the modifications Eric makes to the Morrill Teeny Torque front end to accommodate a spinner. Construction is a cross between traditional balsa-and-tissue and current F1B practice. For example, both the wing and stab use balsa D-boxes combined with carbon-fiber trailing edges. The motor tube and boom are rolled balsa, but the tailboom steps down in size, much like the rolled aluminum-and-carbon Wakefield booms.
Free Flight: Duration
LAST MONTH WE DISCUSSED some of the basics of building two-piece wings. This time we'll look at some of the variations: Straight wing wires are a lot simpler to make and install than bent ones, but what if you don't want a wing with flat center panels? Well, if the wing is thick enough, you can angle the tubes slightly to give some dihedral in the mains. Usually the tubes are located tight against the top of the lower spar at the wing center, and against the bottom of the upper spar a few inches out. The easiest way to do this is to make the main spar as a separate, full-depth subassembly, with hardwood or carbon-fiber top and bottoms spars and a balsa filler in between. Make both main spars and trim to length. Bevel the ends for the desired dihedral.
Free Flight: Duration
NIBBLE 300: Norm Poti's Niblite, featured in a construction article in the October 1995 MA, has a little brother. The Nibble is a 300-square-inch 1/2A/F1J model. Like the Niblite, the Nibble uses a thin, flat-bottom wing with a double-tapered planform. A wide box spar functions like a D-box to stiffen the wing. The fuselage is a carbon tube from Ken Oliver. Power is a Galbreath-prepared C.S. .049. A Seelig Minicombo timer handles the auto functions (VIT, bunt, auto rudder, and DT). Note that the wing overhangs the rear of the pylon; the wing hold-down rubber bands go through a hole in the wing to line up with the rear hook.
Free Flight: Duration
RE-ENTRY VEHICLE: For most of us, Free Flight is a lifetime hobby and sport. We get hooked in our youth, perhaps drift away for a while, and then return. Statistics, and a look around the field at any contest, will show that many of us are well into middle age. As often as not, the beginner in Free Flight isn't really beginning, but picking up where he left off some 20 or 30 years earlier. The memories and experiences of youth were, hopefully, one of the things that pulled this middle-aged "beginner" back to Free Flight. Certainly many of the techniques and skills learned years ago will come in handy. But it is important to get up to speed on the new tools, materials, and methods we use today. Where to start? Unfortunately, a visit to the average hobby shop is going to be next to useless. Sure you can pick up some balsa, new X-Acto blades, and some of that new instant glue, but you probably won't find much else. Free Flight has become almost entirely a mail-order proposition. So the first step to get back in to free flight is order some catalogs.
